VersaFlex FSS 50DM is a fast set, rapid curing, 100% solids, flexible, two-component polyurea elastomer spray coating material. FSS 50DM is used by itself or in combination with other materials to produce coatings, liners, wearing courses, and resilient surfaces on metal and other substrates. 

FSS 50DM produces an extremely tough film at all thicknesses. Single or multiple pass applications produce films from 10 mils to 1,000 mils without appreciable sag or runs. FSS 50DM may be applied in all positions and to any properly prepared substrate. 

FSS 50DM is inert, it will not hydrolyze, leach, or contaminate other materials, and is bondable and paintable. FSS 50DM is relatively moisture and temperature insensitive, allowing application in the most problematic ambient conditions.

Applications & Uses

VersaFlex FSS 50DM is a superior metal coating material designed specifically for industrial applications receiving constant or intermittent attack from contained materials, most corrosive substrates and abrasive action. FSS 50DM may be used to coat any properly prepared substrate. FSS 50DM is flexible, accommodating to movement of the substrate, yet strong enough to remain intact under all conditions except major structural dislocations.

With or without reinforcements, FSS 50DM may be used in transitional areas with confidence. FSS 50DM may be used in interior or exterior applications. FSS 50DM is recommended for repair of other films, may be applied to metal and other substrates, in new construction and in cold weather conditions.

Ideal for Applications In:

• Waterproofing Membrane
• Chemical Plants
• Metal Coating
• Tank Linings
• Secondary Containment
• Liners

Performance Benefits

• Odorless, No VOC's
• 1:1 Mix Ratio by Volume
• Fast Return to Service 
• Rapid Gel Time
• Installation temperature range from -40° to 300°F
• Operating Temperatures  -40° to 350°F

Data Sheets & MSDS Specifications

VersaFlex FSS 50DM MSDS Sheet A

VersaFlex FSS 50DM MSDS Sheet B

VersaFlex FSS 50DM Data Sheet

VersaFlex FSS 50DM Material Processing Sheet

VersaFlex FSS 50DM Chemical Resistance Chart

VersaFlex FSS 45DC is a fast set, rapid gelling, 100% solids, flexible, two- component polyurea elastomer spray coating material. FSS 45DC is used by itself or in combination with other materials to produce coatings, liners, wearing courses, and resilient surfaces on concrete and other substrates.

FSS 45DC produces an extremely tough film at all thicknesses. FSS 45DC may be applied in all positions and to any properly prepared substrate. 

FSS 45DC is inert, it will not hydrolyze, leach, or contaminate other materials, and is bondable and paintable. FSS 45DC is relatively moisture and temperature insensitive, allowing application in the most problematic ambient conditions.

Applications & Uses

VersaFlex FSS 45DC is a superior coating material designed specifically for industrial applications receiving constant or intermittent attack from contained materials, subsurface hydrostatic pressure, most corrosive substances, and abrasive action. FSS 45DC is flexible, accommodating to movement of the substrate, yet strong enough to remain intact under all conditions except major structural dislocations.

With or without reinforcements, FSS 45DC may be used in transitional areas with confidence. FSS 45DC may be used in interior or exterior applications.

Ideal for Applications In:

• Industrial Facilities
• Parking Garage Decks
• Below Grade Waterproofing
• Above Grade Dampproofing
• Water & Waste Water Treatment
• Food Processing Facilities
• Pulp & Paper Mills
• Bottling & Canning Facilities
• Walkways & Balconies
• Secondary Containment

Performance Benefits

• 100% Solids
• No VOC's
• Odorless, No Toxic Vapors
• Tough Elastomeric Membrane 
• Excellent Thermal Stability
• Minimal Downtime
• Low Permeance Rate
• Good Resistance to a Wide Range of Chemical Attack
• USDA Approved
• Operating Temperatures -40°F to 350°F

VersaFlex AquaVers 20 is a two-component isocyanate and resin blend primer for use on a variety of substrates.AquaVers 20 may be diluted to reduce viscosity. AquaVers 20 has a working time of 45 minutes. Ponding on the surface is to be avoided.

VersaFlex AquaVers 20 primer may be used with all VersaFlex rapid curing polyurea sealants and spray coatings systems. It is designed for use in both interior and exterior priming situations.

Performance Benefits

• No VOC’s
• Low viscosity, odorless
• 100% Solids
• Penetrating Sealer
• Formulated as a System with VersaFlex Products
• Reduces pin-holes
• Applied by spray, squeegee, brush or roller
• Increases adhesion of coating to concrete

Data Sheets and MSDS Specifications

AquaVers® 20 Primer Data Sheet

AquaVers® 20 Primer SDS A-side

AquaVers® 20 Primer SDS B-side

AquaVerse® 20 Primer Material Processing